users April 2015

users@lists.genode.org

31 participants
38 discussions

how can i change u-boot load address?
by bharath 29 Apr '15

29 Apr '15

Hi, I have built uImage using Genode OS Framework for IMX6 Sabre SDBoard. I am getting error as cannot get kernel image. My built uImage is 7858662 Bytes = 7.5 MB I used following commands to flash u-boot and uImage respectively (It is a 16GB microsdcard) $sudo dd if=u-Boot-mx6q-sabresd-no-padding.bin of=/dev/sdc bs=512 seek=2 conv=fsync $sudo dd if=uImage of=/dev/* bs=512 seek=2048 conv=fsync When I inserted the SDCard to the board and tried to boot, it is giving the following error: ## Booting kernel from Legacy Image at 10800000 ... Image Name: Image Type: ARM Linux Kernel Image (gzip compressed) Data Size: 7858662 Bytes = 7.5 MB Load Address: 10001000 Entry Point: 10001000 Verifying Checksum ... Bad Data CRC ERROR: can't get kernel image! So, I thought of of changing please try Load Address: 10800000 as per this post. https://community.freescale.com/message/510211#510211 How can I change the Load address. Please suggest.

2 1

Develop TrustZone for iMX6
by bharath 29 Apr '15

29 Apr '15

> please, follow Martin's advice and do not use the outdated RUN_OPT > setting when using u-boot. If you replace it like this: > RUN_OPT += --include image/uboot > You will even find a uImage in your 'var/run/tz_vmm_mx6' folder. Sorry I > was not recognizing that you were using the old, invalid setting for > RUN_OPT when writing my last mail. > I would suggest to build the u-boot uImage automatically via our build > system instead of fiddling around with elf or binary images manually. > Regards > Stefan Hi Stefen, Now, I deleted the total source code, again downloaded and repeated the following steps: $ cd genode-hw_sabrelite_tz_support/tool/ $ ./create_builddir hw_sabrelite_tz BUILD_DIR=build_sabrelite_tz $ make run/tz_vmm_mx6 Now I did not use the RUNOPT. It got successfully built. But I found only image.elf and boot_modules.s in the 'var/run/tz_vmm_mx6' folder. contents of build.conf file in etc folder is as follows: GENODE_DIR = /home/bharath/Bharath/Development/Security/genode- hw_sabrelite_tz_support BASE_DIR = $(GENODE_DIR)/repos/base CONTRIB_DIR = $(GENODE_DIR)/contrib ## ## Kernel-specific base repository ## REPOSITORIES += $(GENODE_DIR)/repos/base-hw ## ## Kernel-specific run tool configuration ## RUN_OPT = --include boot_dir/hw ## ## Repositories needed for the default demo scenario ## REPOSITORIES += $(GENODE_DIR)/repos/base REPOSITORIES += $(GENODE_DIR)/repos/os REPOSITORIES += $(GENODE_DIR)/repos/demo ## ## Optional repositories ## # # Ports of popular open-source libraries and the C library. # # Make sure to execute 'make prepare' in 'libports' prior building. # #REPOSITORIES += $(GENODE_DIR)/repos/libports # # Ports of popular 3rd-party applications # # The 'ports' repository depends on 'libc' and 'libports'. # Make sure to execute 'make prepare' in 'ports' prior building. # #REPOSITORIES += $(GENODE_DIR)/repos/ports # # Ports of the Linux TCP/IP stack and Linux drivers (USB) from the Linux kernel # #REPOSITORIES += $(GENODE_DIR)/repos/dde_linux # # NetBSD file-system support # #REPOSITORIES += $(GENODE_DIR)/repos/dde_rump # # High-level Genode-specific services and applications # # The 'gems' repository depends on 'libc' and 'libports'. # #REPOSITORIES += $(GENODE_DIR)/repos/gems Please suggest.

2 1

run scripts not working
by Nobody III 28 Apr '15

28 Apr '15

I updated to the latest git version of Genode, then tried to build the demo scenario. Unfortunately, it doesn't run on any of the kernels I've tried. Here is the make output relevant to the error: make[1]: Leaving directory '/home/kingtux/genode/build/nova_x86_64' genode build completed wrong # args: should be "run_boot_dir" while executing "run_boot_dir $binaries" (procedure "build_boot_image" line 2) invoked from within "build_boot_image $boot_modules" (file "/home/kingtux/genode/repos/os/run/demo.run" line 221) invoked from within "source $include_name" ("foreach" body line 6) invoked from within "foreach include_name [get_cmd_arg --include ""] { # first check if the include name is absolute if {[string first "/" $include_name] == 0} { puts ..." (file "/home/kingtux/genode/tool/run/run" line 630) Makefile:231: recipe for target 'run/demo' failed make: *** [run/demo] Error 1 What's wrong and how can I fix it?

2 2

Develop TrustZone for iMX6
by bharath 28 Apr '15

28 Apr '15

> Hi Bharath, Stefan > Although Stefan is absolutely right, I'd like to suggest you to NOT > modify the "RUN_OPT = --target uboot" lines to "RUN_OPT += --target > uboot" but to remove them from your build.conf. The "--target uboot" > would be ignored by the run tools anyway and this way you keep your > build.conf content less irritating. > Cheers, > Martin Hi Martin and Stefen, Thanks. Now I tried RUN_OPT += --target uboot. It worked. But image.elf is created in build_sabrelite_tz/var/run/tz_vmm_mx6/ folder. Can I directly dump to the SDCard or should I need to convert to a binary? Cheers, Bharath

2 1

Develop Trustzone support for imx6
by thong 28 Apr '15

28 Apr '15

Hi all, I am a newbie in embedded linux system, and my team is starting to integrate our biometric identification solution into the board i.MX6Q-SABRESD using Secure OS on Trustzone. After take a research around, I decide to try start with Genode on imx53_tablet_demo at https://github.com/skalk/genode/blob/i.MX53_tablet_demo/os/src/server/vmm/i…. I tried to modify base-hw/src/core/kernel/kernel.cc to add a code line PDBG("Hello\n") at the beginning of main routine void kernel() and expected to receive a "Hello" message on my Serial Terminal. I followed the instructions in README and be success to build the Genode with command line: RUN_OPT="--target uboot" make run/printf I use pre-built u-boot-mx6dl-sabresd.bin from Freescale. When I try to boot my Genode build in var/run/printf/ it just stopped at "Starting kernel..." message: U-Boot 2009.08 (Aug 16 2013 - 12:04:20) CPU: Freescale i.MX6 family TO1.2 at 792 MHz Thermal sensor with ratio = 187 Temperature: 48 C, calibration data 0x59e4ff7d mx6q pll1: 792MHz mx6q pll2: 528MHz mx6q pll3: 480MHz mx6q pll8: 50MHz ipg clock : 66000000Hz ipg per clock : 66000000Hz uart clock : 80000000Hz cspi clock : 60000000Hz ahb clock : 132000000Hz axi clock : 264000000Hz emi_slow clock: 132000000Hz ddr clock : 528000000Hz usdhc1 clock : 198000000Hz usdhc2 clock : 198000000Hz usdhc3 clock : 198000000Hz usdhc4 clock : 198000000Hz nfc clock : 24000000Hz Board: i.MX6Q-SABRESD: unknown-board Board: 0x63012 [POR ] Boot Device: SD I2C: ready DRAM: 1 GB MMC: FSL_USDHC: 0,FSL_USDHC: 1,FSL_USDHC: 2,FSL_USDHC: 3 In: serial Out: serial Err: serial i2c: I2C3 SDA is low, start i2c recovery... I2C3 Recovery success Found PFUZE100! deviceid=10,revid=11 Net: got MAC address from IIM: 00:04:9f:02:e0:39 FEC0 [PRIME] Hit any key to stop autoboot: 0 MX6Q SABRESD U-Boot > fatload mmc 2:1 0x20000000 uImage_imx6_tz reading uImage_imx6_tz 359877 bytes read MX6Q SABRESD U-Boot > bootm 20000000 ## Booting kernel from Legacy Image at 20000000 ... Image Name: Image Type: ARM Linux Kernel Image (gzip compressed) Data Size: 359813 Bytes = 351.4 kB Load Address: 10001000 Entry Point: 10001000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK Starting kernel ... I highly appreciate any respond to help me on this. Thank you very much in advance. --Thong Nguyen.

6 17

Re: TrustZone image problem
by bharath 28 Apr '15

28 Apr '15

> Hi Bharath, > Please verify if your build directory has enough space. If it has 100% > utilization, it would have created a truncated uboot image. > Hope this helps, > Thanks > Vasan Hi Vasan, You are saying about enough space in my system where I am building the uImage right? If that is so, Yes I do have enough space. How can we can check whether it is truncated uboot image? When I gave the following command: mkimage -l uImage Image Name: Created: Mon Apr 27 17:58:58 2015 Image Type: ARM Linux Kernel Image (gzip compressed) Data Size: 7858662 Bytes = 7674.47 kB = 7.49 MB Load Address: 10001000 Entry Point: 10001000 This means that I have build correct uImage right?

1 0

TrustZone image problem
by bharath 28 Apr '15

28 Apr '15

Hi, I am trying to run tz_vmm script for imx6 board, I am able to compile the script for imx6 board and it is successfully creating the uImage of size 7.5 MB, But when I am trying to run this image on the board this is giving following error: Booting kernel from Legacy Image at 10800000 ... Image Name: Image Type: ARM Linux Kernel Image (gzip compressed) Data Size: 7858662 Bytes = 7.5 MB Load Address: 10001000 Entry Point: 10001000 Verifying Checksum ... Bad Data CRC ERROR: can't get kernel image! What would be the problem?

3 2

genode manual
by Prashanth Mundkur 28 Apr '15

28 Apr '15

Hi, I'm having trouble building the manual from the latest genode-manual master: <use img/genode_labs.pdf> [150] <use img/genode_labs.pdf> [151] <use img/genode_labs.pdf> [152] ! LaTeX Error: File `spec/classes/genode/capability/description.tex' not found. Type X to quit or <RETURN> to proceed, or enter new name. (Default extension: tex) Enter file name: Being unable to build, I instead read the March 9th version of the really excellent manual, and have the following feedback: - section 3.1.4: Capability delegation through capability invocation Is there a notion of access rights on capabilities, e.g. read/write/grant as in sel4? If not, it might be good to comment on the design choice. - 3.2.4: Client-server relationship Not sure if this is the best place for it, but related to the lifetime of a session, can capabilities be revoked or deleted, and who can perform this action (child/parent/delegatee)? It would be good to have an explanation that is as clear as the one on capability creation and delegation, explaining how a capability is removed from a protection domain. - 3.4.5: Address-space management One issue that was not referred to was handling page-faults, which I found is indeed covered in the 'Under the hood' chapter. It would be good to have a forward reference. I found the sub-section on managed dataspaces a bit unclear, especially the relationship between 'the RM client' and 'the component' in the first case, and 'client', 'RM client' and 'server' in the second case. One (or two) of your excellent diagrams would be really helpful here. - 3.6.1: Synchronous RPC This is not clear: "Each IPC server has a corresponding untyped capability that can be used to perform calls to the server using an IPC client object." Perhaps server/client got swapped somewhere? - 3.6.2: Asynchronous notifications Even when the server is signalling events to a single trusted client, isn't there a possibility of deadlock that motivates the need for asynchronous notifications? - 6.2.6: Assigning subsystems to CPUs At the end of the section, I thought the upper-left CPU would be at position (0,8) instead of (4,0). Perhaps a diagram could help, or the existing diagram showing affinity for nested inits could be reused for this example. Hope this is useful. --prashanth

2 4

Re: Develop Trustzone support for imx6
by chirag garg 28 Apr '15

28 Apr '15

Hello Bharath, As I can see in your log: Download linux binary ...(put your linux file manually) wrong # args: should be "run_boot_dir" It seems that you haven't put the normal world OS image as "linux" in your <Genode_Dir>/build_sabrelite/bin/ folder as the log message clearly says that "put your linux file manually". We have tried with the Genode as normal world OS. I have put one file on the following link you can use this. https://github.com/chiragdthinker/Genode_Binaries/ you can download the linux file from here and put in the above mentioned folder. I think this will solve your problem. Don't hesitate to ask any other doubts on this. Regards Chirag Garg IIT Madras , Rise Lab On Mon, Apr 27, 2015 at 2:32 PM, bharath <bharathkr.bojja@...9...> wrote: > chirag garg <chiragdthinker@...52...> writes: > > > > > > > > > Hello Thong, > > It seems, you are trying to run i.mx53 image on the i.mx6 board if that > is > the case it will not work. To run the printf script over the imx6 platform > you should try out the latest master branch of Genode on git hub that have > the imx6 support without trustzone.https://github.com/genodelabs/genode > > > > For the TrustZone support on imx6 SABRE Lite board our team is also > working at IIT Madras , As of now we are able to run Genode(secure world) > beside Genode(normal world) so you can take a look at IIT Madras repository > as the initial starting point. > > > > Genode as secure world : > https://github.com/iitmadras/genode/tree/hw_sabrelite_tz_supportIn the > hw_sabrelite_tz_support branch tz_vmm_mx6 will work as tz_vmm Genode as > normal world : > https://github.com/iitmadras/genode/tree/hw_sabrelite_tz_normal_os > > Switch application in the hw_sabrelite_tz_normal_os branch will serve you > as a linux (for normal world) kernel image in tz_vmm. > > > > > > > > Regards > > Chirag Garg > > IIT Madras , Rise Lab > > > > On Tue, Apr 21, 2015 at 8:20 AM, thong <thong- > kmCu2mEWxz5BDgjK7y7TUQ@...325...> wrote:Hi all, > > I am a newbie in embedded linux system, and my team is starting to > > integrate our biometric identification solution into the board > > i.MX6Q-SABRESD using Secure OS on Trustzone. After take a research > > around, I decide to try start with Genode on imx53_tablet_demo > athttps:// > github.com/skalk/genode/blob/i.MX53_tablet_demo/os/src/server/vmm/ > imx53/README. > > I tried to modify base-hw/src/core/kernel/kernel.cc to add a code line > > PDBG("Hello\n") at the beginning of main routine void kernel() and > > expected to receive a "Hello" message on my Serial Terminal. I followed > > the instructions in README and be success to build the Genode with > > command line: > > RUN_OPT="--target uboot" make run/printf > > I use pre-built u-boot-mx6dl-sabresd.bin from Freescale. > > When I try to boot my Genode build in var/run/printf/ it just stopped at > > "Starting kernel..." message: > > U-Boot 2009.08 (Aug 16 2013 - 12:04:20) > > CPU: Freescale i.MX6 family TO1.2 at 792 MHz > > Thermal sensor with ratio = 187 > > Temperature: 48 C, calibration data 0x59e4ff7d > > mx6q pll1: 792MHz > > mx6q pll2: 528MHz > > mx6q pll3: 480MHz > > mx6q pll8: 50MHz > > ipg clock : 66000000Hz > > ipg per clock : 66000000Hz > > uart clock : 80000000Hz > > cspi clock : 60000000Hz > > ahb clock : 132000000Hz > > axi clock : 264000000Hz > > emi_slow clock: 132000000Hz > > ddr clock : 528000000Hz > > usdhc1 clock : 198000000Hz > > usdhc2 clock : 198000000Hz > > usdhc3 clock : 198000000Hz > > usdhc4 clock : 198000000Hz > > nfc clock : 24000000Hz > > Board: i.MX6Q-SABRESD: unknown-board Board: 0x63012 [POR ] > > Boot Device: SD > > I2C: ready > > DRAM: 1 GB > > MMC: FSL_USDHC: 0,FSL_USDHC: 1,FSL_USDHC: 2,FSL_USDHC: 3 > > In: serial > > Out: serial > > Err: serial > > i2c: I2C3 SDA is low, start i2c recovery... > > I2C3 Recovery success > > Found PFUZE100! deviceid=10,revid=11 > > Net: got MAC address from IIM: 00:04:9f:02:e0:39 > > FEC0 [PRIME] > > Hit any key to stop autoboot: 0 > > MX6Q SABRESD U-Boot > fatload mmc 2:1 0x20000000 uImage_imx6_tz > > reading uImage_imx6_tz > > 359877 bytes read > > MX6Q SABRESD U-Boot > bootm 20000000 > > ## Booting kernel from Legacy Image at 20000000 ... > > Image Name: > > Image Type: ARM Linux Kernel Image (gzip compressed) > > Data Size: 359813 Bytes = 351.4 kB > > Load Address: 10001000 > > Entry Point: 10001000 > > Verifying Checksum ... OK > > Uncompressing Kernel Image ... OK > > Starting kernel ... > > I highly appreciate any respond to help me on this. > > Thank you very much in advance. > > --Thong Nguyen. > > > -------------------------------------------------------------------------- > ---- > > BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT > > Develop your own process in accordance with the BPMN 2 standard > > Learn Process modeling best practices with Bonita BPM through live > exerciseshttp://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- > event?utm_ > > source=Sourceforge_BPM_Camp_5_6_15&utm_medium=email&utm_campaign=VA_SF > > _______________________________________________ > > genode-main mailing listgenode-main- > 5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f > @public.gmane.orghttps://lists.sourceforge.n > et/lists/listinfo/genode-main > > > > > > > > > > > > > > > -------------------------------------------------------------------------- > ---- > > BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT > > Develop your own process in accordance with the BPMN 2 standard > > Learn Process modeling best practices with Bonita BPM through live > exercises > > http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event? > utm_ > > source=Sourceforge_BPM_Camp_5_6_15&utm_medium=email&utm_campaign=VA_SF > > > > _______________________________________________ > > genode-main mailing list > > genode-main@...52... > > https://lists.sourceforge.net/lists/listinfo/genode-main > > > > Hi, > > I have downloaded genode-hw_sabrelite_tz_support for Genode as secure world > in the following link: > https://github.com/iitmadras/genode/tree/hw_sabrelite_tz_support > > I tried build by the following steps: > cd genode-hw_sabrelite_tz_support/tools/ > ./create_builddir hw_sabrelite_tz BUILD_DIR=build_sabrelite > cd build_sabrelite/ > RUN_OPT="--target uboot" > make run/tz_vmm_mx6 > > It is giving the following error: > > including genode-hw_sabrelite_tz_support/repos/os/run/tz_vmm_mx6.run > building targets: core init server/tz_vmm > spawn make core init server/tz_vmm > make[1]: Entering directory `genode- > hw_sabrelite_tz_support/tool/build_sabrelite' > checking library dependencies... > Skip target server/tz_vmm/imx53_qsb because it requires hw_imx53_qsb > platform_imx53 > Skip target server/tz_vmm/usb_armory because it requires hw_usb_armory > platform_imx53 > Library platform > MERGE platform.lib.a > Library cxx > COMPILE exception.o > COMPILE guard.o > COMPILE malloc_free.o > COMPILE misc.o > COMPILE new_delete.o > COMPILE unwind.o > MERGE supc++.o > CONVERT supc++.o > MERGE cxx.lib.a > Library base-common > COMPILE allocator/allocator_avl.o > COMPILE allocator/slab.o > COMPILE avl_tree/avl_tree.o > COMPILE child/child.o > COMPILE console/console.o > COMPILE elf/elf_binary.o > COMPILE heap/heap.o > COMPILE heap/sliced_heap.o > COMPILE ipc/ipc.o > COMPILE ipc/ipc_marshal_cap.o > COMPILE kernel/interface.o > COMPILE lock/lock.o > COMPILE process/process.o > COMPILE server/common.o > COMPILE server/server.o > COMPILE signal/common.o > COMPILE signal/platform.o > COMPILE signal/signal.o > COMPILE thread/bootstrap.o > COMPILE thread/context_allocator.o > COMPILE thread/trace.o > MERGE base-common.lib.a > Library syscall > MERGE syscall.lib.a > Library startup > COMPILE _main.o > ASSEMBLE crt0.o > COMPILE init_main_thread.o > MERGE startup.lib.a > Library base > COMPILE console/log_console.o > COMPILE cpu/cache.o > COMPILE env/context_area.o > COMPILE env/env.o > COMPILE env/reinitialize.o > COMPILE thread/start.o > COMPILE thread/thread.o > MERGE base.lib.a > Library init_pd_args > COMPILE pd_args.o > MERGE init_pd_args.lib.a > Library config > COMPILE config.o > MERGE config.lib.a > Program init/init > COMPILE main.o > LINK init > Program server/tz_vmm/imx6/tz_vmm > COMPILE main.o > LINK tz_vmm > Library core-perf_counter_on > COMPILE spec/arm_v7/perf_counter.o > MERGE core-perf_counter_on.lib.a > Library core-perf_counter > MERGE core-perf_counter.lib.a > Library core-trustzone_on > COMPILE _main.o > ASSEMBLE boot_modules.o > COMPILE console.o > COMPILE context_area.o > COMPILE core_mem_alloc.o > COMPILE core_rm_session.o > COMPILE cpu_session_component.o > COMPILE cpu_session_support.o > COMPILE dataspace_component.o > COMPILE dump_alloc.o > COMPILE init_main_thread.o > COMPILE io_mem_session_component.o > COMPILE io_mem_session_support.o > COMPILE irq_session_component.o > COMPILE kernel/cpu.o > COMPILE kernel/irq.o > COMPILE kernel/kernel.o > COMPILE kernel/pd.o > COMPILE kernel/signal_receiver.o > COMPILE kernel/thread.o > COMPILE main.o > COMPILE pager.o > COMPILE pd_session_component.o > COMPILE platform.o > COMPILE platform_pd.o > COMPILE platform_thread.o > COMPILE ram_session_component.o > COMPILE ram_session_support.o > COMPILE rm_session_component.o > COMPILE rm_session_support.o > COMPILE rom_session_component.o > COMPILE signal_session_component.o > COMPILE spec/arm/cpu.o > ASSEMBLE spec/arm/crt0.o > COMPILE spec/arm/kernel/cpu.o > COMPILE spec/arm/kernel/cpu_context.o > ASSEMBLE spec/arm/kernel/crt0.o > COMPILE spec/arm/kernel/thread.o > COMPILE spec/arm/kernel/thread_base.o > COMPILE spec/arm/platform_support.o > COMPILE spec/arm_v7/cpu.o > COMPILE spec/arm_v7/kernel/vm_thread.o > ASSEMBLE spec/arm_v7/mode_transition.o > COMPILE spec/arm_v7/trustzone/kernel/vm.o > COMPILE spec/arm_v7/trustzone/kernel/vm_thread.o > ASSEMBLE spec/arm_v7/trustzone/mode_transition.o > COMPILE spec/arm_v7/trustzone/vm_session_component.o > COMPILE spec/arm_v7/vm_session_component.o > COMPILE spec/imx6/trustzone/pic.o > COMPILE spec/imx6/trustzone/platform_services.o > COMPILE spec/imx6/trustzone/platform_support.o > COMPILE thread/thread.o > COMPILE thread_start.o > COMPILE trace_session_component.o > COMPILE version.o > MERGE core-trustzone_on.lib.a > Library core-trustzone > MERGE core-trustzone.lib.a > Library core > MERGE core.lib.a > Program core/core > COMPILE kernel/test.o > LINK core > make[1]: Leaving directory `genode- > hw_sabrelite_tz_support/tool/build_sabrelite' > genode build completed > Download initramfs ... > Download linux binary ...(put your linux file manually) > wrong # args: should be "run_boot_dir" > while executing > "run_boot_dir $binaries" > (procedure "build_boot_image" line 2) > invoked from within > "build_boot_image "core init tz_vmm linux initrd.gz"" > (file "genode-hw_sabrelite_tz_support/repos/os/run/tz_vmm_mx6.run" line > 49) > invoked from within > "source $include_name" > ("foreach" body line 6) > invoked from within > "foreach include_name [get_cmd_arg --include ""] { > # first check if the include name is absolute > if {[string first "/" $include_name] == 0} { > puts ..." > (file "genode-hw_sabrelite_tz_support/tool/run/run" line 630) > make: *** [run/tz_vmm_mx6] Error 1 > > What will be the problem? > > ------------------------------------------------------------------------------ > One dashboard for servers and applications across Physical-Virtual-Cloud > Widest out-of-the-box monitoring support with 50+ applications > Performance metrics, stats and reports that give you Actionable Insights > Deep dive visibility with transaction tracing using APM Insight. > http://ad.doubleclick.net/ddm/clk/290420510;117567292;y > _______________________________________________ > genode-main mailing list > genode-main(a)lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/genode-main >

2 1

Documentation - request for feedback
by Norman Feske 27 Apr '15

27 Apr '15

Hello, according to our road map (http://genode.org/about/road-map), the upcoming Genode version 15.05 will be accompanied with comprehensive documentation. The work on this documentation is in full swing and can be tracked at the corresponding Git repository: https://github.com/nfeske/genode-manual A snapshot of the current version is available as PDF at: http://genode.org/files/53bcb8e33fe6602fed25edc3c7b922c5/manual-2015-03-06.… So far, the work on the following chapters is completed already: 3. Architecture 4. Components 6. System configuration 8. Under the hood I would greatly appreciate feedback from the community about those chapters - be it in the form of minor spelling or grammar fixes, suggestions for additional topics you wish to see covered, hints about misleading paragraphs, or any other concerns that you may have. Cheers Norman -- Dr.-Ing. Norman Feske Genode Labs http://www.genode-labs.com · http://genode.org Genode Labs GmbH · Amtsgericht Dresden · HRB 28424 · Sitz Dresden Geschäftsführer: Dr.-Ing. Norman Feske, Christian Helmuth

7 11

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

users April 2015