Hi Stefan,
Thank you so much. I will check out some Android developer forums.
But for now, I tried it in a different way. Unlike your demo in this article https://github.com/skalk/genode/blob/i.MX53_tablet_demo/os/src/server/vmm/imx53/README, I wanted the display to be usable only by the normal world (Linux/Android kernel). So I have downloaded the pre-built Linux/Android kernel uImage binary for i.mx53QSB from Adeneo Embedded website ( http://www.adeneo-embedded.com/en/Products/Board-Support-Packages/Freescale-...) and copy the binary to the 'bin' subdirectory of the Genode build directory. I have also marked like I2C, GPIO and IPU as unsecure devices in the csu.h file. However, I got a data abort error (see attached) at boot time. Could you please tell me what is wrong?
Thanks and best regards,
On Fri, Jan 8, 2016 at 8:53 AM, Stefan Kalkowski < stefan.kalkowski@...1...> wrote:
Hi,
On 01/05/2016 11:34 PM, Joseph Lee wrote:
Hi Stefan,
Thanks a lot for your explanation.
when i reset the GPU to be unsecure in csu.h file, it displays the
attached
output and gets stuck again. I assume a user prompt will appear in the
end
to execute Linux commands. is that right? what does "sh: can't access
tty;
job control turned off" error mean?
whether you will see a shell prompt on the serial line fully depends on the initramfs and the android services that are under your control. As I already said the original example you have adapted depends on the display driver etc. which doesn't seem to be incorporated into your run script.
The message "sh: can't access tty; job control turned off" point to the fact that your initramfs starts a shell in the end (with other words the linux boot process finished) but it isn't writing to a proper tty, thereby it does not support e.g.: background processes or in general "job control". Probably it does not use the right serial tty in your initramfs. Does the /dev/ttymxc0 file exists within your initramfs, or is it created via udev or android configuration? What I can see from your output is, that you are still using the same kernel command line parameters like in the automated tz_vmm run-script version. In the old android demonstration scenario we used the following additional parameters: "androidboot.console=ttymxc0 video=mxcdi1fb:RGB666,XGA gpu_memory=64M lpj=4997120". Although the video and lpj parameter probably must be different when using the Quickstart board instead of the tablet, the console parameter should be important for android.
To be honest, I'm no expert for bootstrapping an Android system. Although, I brought that Android example on top of Genode/TrustZone to life, I'm not so much familiar with the internals of the Android configuration system. So if you are dealing with problems here, it might be valueable to look into Android porting howtos and Android system developer forums.
Best regards Stefan
Thanks,
On Tue, Jan 5, 2016 at 8:47 AM, Stefan Kalkowski < stefan.kalkowski@...1...> wrote:
Hi Joseph,
On 01/05/2016 01:49 AM, Joseph Lee wrote:
Hello everyone,
I have built and run the current Genode version(15.11) with trustzone
for
hw_imx53_qsb_tz platform but i used the initramfs (initrd.gz) for
Android
image that are used in the demo for Sabre tablet (
https://github.com/skalk/genode/blob/i.MX53_tablet_demo/os/src/server/vmm/im...
).
That is right, one has to distinguish between Sabre Tablet and Quickstart Board on different levels including the Android images. There might be more surprises when porting the existent demo to the Quickstart board.
After some trials and errors, I have managed to get the following
outputs
(see attached) on the serial console and it got stuck. is this the
right
approach to run Android in the normal world of i.mx53 QSB? What is
missing
? lvds display is connected to the board but nothing is displayed.
When looking at the attached output I cannot see any initialization of drivers (e.g.: the framebuffer driver). It looks to me as if you are using the current 'tz_vmm' run-script that is used for automated testing only without any graphical setup. Is that right? As an alternative, you might use the run script from the tablet demo as a starting point:
https://raw.githubusercontent.com/skalk/genode/i.MX53_tablet_demo/os/run/vmm...
But again, you must brace yourself for surprises, because the run-script is pretty much outdated and was created for a very specific setup on top of the SABRE tablet.
Apart from that, the output really looks good, but in the end your Android VM faults when trying to access the GPU (data-abort at physical address 0x30001740). That is because the GPU is set as secure within the kernel device initialization (more precisely the Central Security Unit initialization) in file: repos/base-hw/src/core/include/spec/imx53/trustzone/csu.h
The GPU is set as secure like the "Image Processing Unit" (framebuffer device), because we enabled the DMA channel of the framebuffer driver to access secure memory, as it is driven by Genode's framebuffer driver that runs within the secure world. Sadly the GPU device uses the same DMA channel ID, and thereby the GPU is allowed to access secure memory via DMA too. Therefore, we set the GPU to be used by the secure world
only.
If you want to use the GPU within the normal world (Android) for demonstration purposes only, and do not matter about DMA device attacks, you can also re-set the GPU to be unsecure (search for GPU 2D and 3D in the csu.h file).
Regards Stefan
Thanks,
On Mon, Dec 28, 2015 at 4:48 AM, Joseph Lee <leejose911@...9...>
wrote:
Hi everyone,
i am currently trying to run trustzone demo on imx53 Quick Start Board (qsb). In which i want to run Android OS in the normal world. i
followed
the instruction in this link (
https://github.com/skalk/genode/blob/i.MX53_tablet_demo/os/src/server/vmm/im...
)
and built the uImage successfully. I put the uImage on the SD card partition (/dev/mmcblk0p1). However, when try to boot the uImage, it
gets
stuck after displaying the following outputs. I have attached the
whole
log
messages. FYI, the SD card has two partitions(/dev/mmcblk0p1 and /dev/mmcblk0p2) with ext4 format.
mmc0: new high speed SDHC card at address 0007 mmcblk0: mmc0:0007 SD32G 28.9 GiB mmcblk0: p1 p2 init: cannot open '/initlogo.rle' EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) EXT4-fs (mmcblk0p2): re-mounted. Opts: (null) init: Unable to open persistent property directory /data/property
errno: 2
init: cannot find '/system/bin/sh', disabling 'console' init: cannot find '/system/bin/servicemanager', disabling
'servicemanager'
init: cannot find '/system/bin/vold', disabling 'vold' init: cannot find '/system/bin/netd', disabling 'netd' init: cannot find '/system/bin/dispd', disabling 'dispd' init: cannot find '/system/bin/debuggerd', disabling 'debuggerd' init: cannot find '/system/bin/app_process', disabling 'zygote' init: cannot find '/system/bin/mediaserver', disabling 'media' init: cannot find '/system/bin/dbus-daemon', disabling 'dbus' init: cannot find '/system/bin/installd', disabling 'installd' init: cannot find '/system/etc/install-recovery.sh', disabling 'flash_recovery' init: cannot find '/system/bin/keystore', disabling 'keystore' init: cannot find '/system/bin/rild', disabling 'ril-daemon' init: cannot find '/system/bin/magd', disabling 'magd' init: cannot find '/system/bin/wlan_tool', disabling 'wlan_tool'
could you please let me know what is missing?
thank you!
genode-main mailing list genode-main@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/genode-main
-- Stefan Kalkowski Genode Labs
genode-main mailing list genode-main@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/genode-main
genode-main mailing list genode-main@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/genode-main
-- Stefan Kalkowski Genode Labs
http://www.genode-labs.com/ · http://genode.org/
genode-main mailing list genode-main@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/genode-main