Hi Yevgeny,
congratulations for the first successful steps. Obviously the UART configuration is not proper. One potential problem can be the UART reference clock setting, original value:
repos/base/include/spec/odroid_xu/drivers/board_base.h:31:
The reference clock's value is used to calculate the settings for the appropriated baudrate. Are you using the baudrate 115200 in your UART terminal? Because this is the baudrate the kernel configures the UART to use.
Alternatively, you can skip re-configuration of the UART device by uncommenting the 'Exynos_uart_base' constructor's body, here:
repos/base/include/spec/exynos/drivers/uart_base.h:213
Thereby, you leave the UART settings like u-boot configured it.
Regards Stefan
On 01/04/2017 01:18 AM, Yevgeny Lavrov wrote:
Hello
I've followed all the steps suggested above. There were no problems interacting with Linux system on test board via UART cable. It looks like Network boot and fastboot (Odroid-XU4 doesn't have USB otg port) are not supported by Odroid-XU4. After creating hw_odroid_xu build directory, adding suggested RUN_OPT to build.conf file and executing make run/log I end up with the following output:
spawn fastboot -s usb:2-1.8 boot var/run/log/uImage < waiting for device > Loading timed out Load step failed, retry. spawn fastboot -s usb:2-1.8 boot var/run/log/uImage < waiting for device >
So it appears that fastboot can't find the device. Running *$ sudo fastboot devices -l* returned no results. Probably the reason for this is that I'm connected to Odroid via UART cable. So I gave it another try, using fatload option.
- Copied *uImage* &*image.elf* from *<build-dir>/var/run/log/* over to
the first partition of my MicroSD card 2. Connected to Odroid via UART cable, powered it on and interrupted the boot sequence
then: Exynos5422 # fatload mmc 0 0x48000000 uImage there are pending interrupts 0x00000001 reading uImage
540242 bytes read Exynos5422 # bootm 0x48000000
Result:
## Booting kernel from Legacy Image at 48000000 ... Image Name: Image Type: ARM Linux Kernel Image (gzip compressed) Data Size: 540178 Bytes = 527.5 KiB Load Address: 80000000 Entry Point: 80000000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK Starting kernel ... 7ၷ`�##������@�����������7ٷ`�##��������@�����##��@...470...@...467...` `hqioh~�#@@@��@...470...@...468...``````a�~�##��@...470...@��oi��gp@@��@...470...@...469...```fg�h#@��@...470...@�� pnia�h##�a`v@��p��h`p@@�q@...470...#
image.elf gave me the same output.
Any suggestions on what goes wrong and which way to move next?
Regards
On Thu, Dec 1, 2016 at 5:08 AM, Stefan Kalkowski <stefan.kalkowski@...1... mailto:stefan.kalkowski@...1...> wrote:
sorry, I just recognized the SoCs are not fully equal. The first Odroid XU, which we are using is Exynos 5410, and your board uses Exynos 5422. Anyway, I would follow the same approach. Additionally, you can compare memory settings and I/O memory settings of the UART within device-tree specifications of the two boards: https://raw.githubusercontent.com/torvalds/linux/master/arch/arm/boot/dts/exynos5410-odroidxu.dts <https://raw.githubusercontent.com/torvalds/linux/master/arch/arm/boot/dts/exynos5410-odroidxu.dts> and: https://raw.githubusercontent.com/torvalds/linux/master/arch/arm/boot/dts/exynos5422-odroidxu4.dts <https://raw.githubusercontent.com/torvalds/linux/master/arch/arm/boot/dts/exynos5422-odroidxu4.dts> Regards Stefan On 12/01/2016 10:42 AM, Stefan Kalkowski wrote: > Hello Yevgeny Lavrov, > > there is basic support for the Odroid XU regarding Genode's own kernel > (base-hw). I assume you will be able to start various scenarios that > only use CPU, Timers and UART on the Odroid XU4 as well, because they > use the same SoC. > > I would start with connecting a UART cable via the GPIO ports to your > home computer, and test whether you can interact with a Linux system > running on top of your test board. After that, you might play with > u-boot until you can successfully boot over network, e.g., a Linux > kernel. Possibly, you cannot even network boot on Odroid XU4, but have > to use fastboot (via USB) instead. > > Finally, you start your Genode development by creating a 'hw_odroid_xu' > build directory, add some RUN_OPT variables to the 'etc/build.conf' to > automatically load the setup and interact with the test board, > corresponding to the method you are using (either network boot or > fastboot). Here is some example for the Odroid variant we are testing > nightly: > > RUN_OPT += --include image/uboot > RUN_OPT += --include load/fastboot > RUN_OPT += --load-fastboot-device 'usb:2-1.8' > RUN_OPT += --include log/serial > > Then you can start some very basic example, like: > > make run/log > > and wait, whether you get some output, and if the test succeeds. > > For a general introduction to the build environment and run-script > automatisms, have a look at the Genode foundations: > > https://genode.org/documentation/genode-foundations-16-05.pdf <https://genode.org/documentation/genode-foundations-16-05.pdf> > > In general, it is a good idea to first skim through this document. > > Best regards, > Stefan > > On 12/01/2016 09:12 AM, Yevgeny Lavrov wrote: >> Greetings >> >> I would like to try Genode on Odroid-XU4. I aware that there's no >> support available for this ARM device yet. However, I want to give it a >> try, but I don't know where to start. Can you please point me in the >> right direction so I can find the information that I'll need to get >> started this task? >> >> Thanks >> >> >> ------------------------------------------------------------------------------ >> >> >> >> _______________________________________________ >> genode-main mailing list >> genode-main@lists.sourceforge.net <mailto:genode-main@lists.sourceforge.net> >> https://lists.sourceforge.net/lists/listinfo/genode-main <https://lists.sourceforge.net/lists/listinfo/genode-main> >> > -- Stefan Kalkowski Genode Labs https://github.com/skalk · http://genode.org/ ------------------------------------------------------------------------------ _______________________________________________ genode-main mailing list genode-main@lists.sourceforge.net <mailto:genode-main@lists.sourceforge.net> https://lists.sourceforge.net/lists/listinfo/genode-main <https://lists.sourceforge.net/lists/listinfo/genode-main>
Check out the vibrant tech community on one of the world's most engaging tech sites, SlashDot.org! http://sdm.link/slashdot
genode-main mailing list genode-main@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/genode-main