Sculpt 23.10 Release Candidate

[Pirmin Duss]

Hello Christian

On 10/10/23 11:24, Christian Helmuth wrote:
> Hello Sculpt users,
> 
> we entered the testing phase for the upcoming Sculpt 23.10. Before the
> final release, we like to invite early adopters to give our release
> candidate a try and report back experiences (or issues) with their use
> cases.
> 
> The current candidate is RC4 and can be retrieved via the "System ->
> Update" dialog in entry https://depot.genode.org/chelmuth of your
> current Sculpt installation. Alternatively, you may download the image
> from the following URL.
> 
>    https://depot.genode.org/chelmuth/image/sculpt-pc-2023-10-10.img.xz

I did give the image a quick try on my i7 11700 desktop.

When I try to activate the wired network I get the following output:


[init -> nic_drv] time-clocksource: dde_counter: mask: 0xffffffffffffff 
max_cycles: 0x1d854df40, max_idle_ns: 3526361616960 ns
[init -> nic_drv] time-clocksource: jiffies: mask: 0xffffffff 
max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[init -> nic_drv] time-clocksource: Switched to clocksource dde_counter
[init -> nic_drv] e1000-e1000_main: Intel(R) PRO/1000 Network Driver
[init -> nic_drv] e1000-e1000_main: Copyright (c) 1999-2006 Intel 
Corporation.
[init -> nic_drv] e1000e-netdev: Intel(R) PRO/1000 Network Driver
[init -> nic_drv] e1000e-netdev: Copyright(c) 1999 - 2015 Intel Corporation.
[init -> nic_drv] realtek-r8169_main 07:00.0 eth0: RTL8168e/8111e, 
08:be:ac:22:6c:52, XID 2c2, IRQ 21
[init -> nic_drv] realtek-r8169_main 07:00.0 eth0: jumbo features 
[frames: 9194 bytes, tx checksumming: ko]
[init -> nic_drv] sched_clock: Marking stable (135525000, 
255074000)->(417182000, -26583000)
[init -> nic_drv] realtek-r8169_main 07:00.0: Unable to load firmware 
rtl_nic/rtl8168e-2.fw (-1)
[init -> nic_drv] RTL8211DN Gigabit Ethernet r8169-0-0:00: attached PHY 
driver (mii_bus:phy_addr=r8169-0-0:00, irq=MAC)
[init -> nic_drv] realtek-r8169_main 07:00.0 eth0: No native access to 
PCI extended config space, falling back to CSI
[init -> nic_drv] Error: Function pcie_capability_clear_and_set_word not 
implemented yet!
[init -> nic_drv] Backtrace follows:
Error: illegal READ at address 0xfffffffffffa77b8 by pager_object: 
pd='init -> nic_drv' thread='ep' ip=0x10a8330

The card is plugged to one of the PCIe ports, as the onboard controller 
is an Intel IGC 2.5GB adapter.

Linux reports (`lspci -vv`):
07:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. 
RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 06)
	Subsystem: Realtek Semiconductor Co., Ltd. Device 0123
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 19
	Region 0: I/O ports at 3000 [size=256]
	Region 2: Memory at 6010904000 (64-bit, prefetchable) [size=4K]
	Region 4: Memory at 6010900000 (64-bit, prefetchable) [size=16K]
	Capabilities: <access denied>
	Kernel driver in use: r8169
	Kernel modules: r8169

dmesg:
[    1.535318] r8169 0000:07:00.0: enabling device (0000 -> 0003)
[    1.535415] r8169 0000:07:00.0: can't disable ASPM; OS doesn't have 
ASPM control
[    1.537162] r8169 0000:07:00.0 eth0: RTL8168e/8111e, 
08:be:ac:22:6c:52, XID 2c2, IRQ 153
[    1.537165] r8169 0000:07:00.0 eth0: jumbo features [frames: 9194 
bytes, tx checksumming: ko]
[    4.922396] r8169 0000:07:00.0 enp7s0: renamed from eth0
[   14.174715] RTL8211DN Gigabit Ethernet r8169-0-700:00: attached PHY 
driver (mii_bus:phy_addr=r8169-0-700:00, irq=MAC)
[   14.461989] r8169 0000:07:00.0 enp7s0: Link is Down
[   17.257971] r8169 0000:07:00.0 enp7s0: Link is Up - 1Gbps/Full - flow 
control rx/tx

I will check on the week end if the card works with an older sculpt 
version, as I never have used it with sculpt. My main use case up until 
now was to do iPXE-boot with it while testing the driver for the Intel 
IGC nic.

Regards,
Pirmin