usb issues on AMD 9xx chipset

[Chris Rothrock]

if you don't load the usb_drv, does the platform_drv still run out of caps?

On Sat, Mar 31, 2018 at 2:46 AM, Nobody III <hungryninja101 at ...9...>
wrote:

> I've been testing Genode's current compatibility with my desktop computer,
> which has an AMD 9xx chipset. While the framebuffer driver works fine,
> usb_drv does not.
>
> Here's the full output:
>
> Genode 18.02-2-g6888094f6 <local changes>
> 16299 MiB RAM and 63253 caps assigned to init
> [init -> acpi_drv] Found MADT
> [init -> acpi_drv] MADT IRQ 0 -> GSI 2 flags: 0
> [init -> acpi_drv] MADT IRQ 9 -> GSI 9 flags: 15
> [init -> acpi_drv] Found MCFG
> [init -> acpi_drv] MCFG BASE 0xe0000000 seg 0x0 bus 0x0-0xff
> [init -> platform_drv] 0:2.0 - bridge 1:0.0
> [init -> platform_drv] 0:9.0 - bridge 2:0.0
> [init -> platform_drv] 0:14.4 - bridge 3:0.0
> [init -> platform_drv] 0:15.0 - bridge 4:0.0
> [init -> platform_drv] 0:15.3 - bridge 5:0.0
> [init -> usb_drv] Could not read screen resolution in config node
> [init -> usb_drv] Configured HID screen with 0x0 (multitouch=false)
> [init -> usb_drv] No <storage> config node found - not starting the USB
> Storage (Block) service
> [init -> usb_drv] No <nic> config node found - not starting the USB Nic
> (Network) service
> [init -> usb_drv] No <raw> config node found - not starting external USB
> service
> [init -> usb_drv] Enabled UHCI (USB 1.0/1.1) support
> [init -> usb_drv] Enabled OHCI (USB 1.0/1.1) support
> [init -> usb_drv] Enabled EHCI (USB 2.0) support
> [init -> usb_drv] Enabled XHCI (USB 3.0) support
> *[init -> platform_drv] Warning: Out_of_caps during Device_component
> construction*
> *[init -> platform_drv] Warning: Out_of_caps during Device_component
> construction*
> *[ 0] sys_assign_pci: Invalid Hint (0x200)*
> [init -> platform_drv] Error: usb_drv -> : assignment of PCI device 2:0.0
> failed phys=0xe0200000 virt=0x80400000
> [init -> usb_drv] ioremap: mapped phys 0xfe100000 (size 32768) to virt
> 0x20000
> [init -> usb_drv] dev_info: xHCI Host Controller
> [init -> usb_drv] dev_info: new USB bus registered, assigned bus number 1
> [init -> usb_drv] dev_info: hcc params 0x040040a5 hci version 0x100 quirks
> 0x00000010
> [init -> platform_drv] 2:0.0 adjust IRQ as reported by ACPI: 10 -> 48
> [init -> platform_drv] 2:0.0 uses MSI 64bit, vector 0x9f, address
> 0xfee10000, maskable
> [init -> usb_drv] dev_info: USB hub found
> [init -> usb_drv] dev_info: 4 ports detected
> [init -> usb_drv] dev_info: xHCI Host Controller
> [init -> usb_drv] dev_info: new USB bus registered, assigned bus number 2
> [init -> usb_drv] dev_info: We don't know the algorithms for LPM for this
> host, disabling LPM.
> [init -> usb_drv] dev_info: USB hub found
> [init -> usb_drv] dev_info: 4 ports detected
> [ 0] sys_assign_pci: Invalid Hint (0xb2)
> [init -> platform_drv] Error: usb_drv -> : assignment of PCI device 0:16.2
> failed phys=0xe00b2000 virt=0x1000
> [init -> usb_drv] ioremap: mapped phys 0xfe204000 (size 256) to virt
> 0x17000
> [init -> usb_drv] dev_info: EHCI Host Controller
> [init -> usb_drv] dev_info: new USB bus registered, assigned bus number 3
> [init -> usb_drv] dev_info: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy
> qh workaround
> [init -> platform_drv] 0:16.2 adjust IRQ as reported by ACPI: 11 -> 17
> [init -> platform_drv] 0:16.2 uses IRQ, vector 0x11, non-maskable
> [init -> usb_drv] dev_info: irq 130, io mem 0xfe204000
> [init -> usb_drv] dev_info: USB 2.0 started, EHCI 1.00
> [init -> usb_drv] dev_info: USB hub found
> [init -> usb_drv] dev_info: 4 ports detected
> [ 0] sys_assign_pci: Invalid Hint (0x9a)
> [init -> platform_drv] Error: usb_drv -> : assignment of PCI device 0:13.2
> failed phys=0xe009a000 virt=0x1000
> [init -> usb_drv] ioremap: mapped phys 0xfe207000 (size 256) to virt
> 0x28000
> [init -> usb_drv] dev_info: EHCI Host Controller
> [init -> usb_drv] dev_info: new USB bus registered, assigned bus number 4
> [init -> usb_drv] dev_info: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy
> qh workaround
> [init -> platform_drv] 0:13.2 adjust IRQ as reported by ACPI: 11 -> 17
> [init -> platform_drv] 0:13.2 uses IRQ, vector 0x11, non-maskable
> [init -> usb_drv] dev_info: irq 131, io mem 0xfe207000
> [init -> usb_drv] dev_info: USB 2.0 started, EHCI 1.00
> [init -> usb_drv] dev_info: USB hub found
> [init -> usb_drv] dev_info: 5 ports detected
> [ 0] sys_assign_pci: Invalid Hint (0x92)
> [init -> platform_drv] Error: usb_drv -> : assignment of PCI device 0:12.2
> failed phys=0xe0092000 virt=0x1000
> [init -> usb_drv] ioremap: mapped phys 0xfe209000 (size 256) to virt
> 0x29000
> [init -> usb_drv] dev_info: EHCI Host Controller
> [init -> usb_drv] dev_info: new USB bus registered, assigned bus number 5
> [init -> usb_drv] dev_info: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy
> qh workaround
> [init -> platform_drv] 0:12.2 adjust IRQ as reported by ACPI: 11 -> 17
> [init -> platform_drv] 0:12.2 uses IRQ, vector 0x11, non-maskable
> [init -> usb_drv] dev_info: irq 132, io mem 0xfe209000
>
> Also, I get the following message in dmesg on linux (from
> drivers/usb/host/pci-quirks.c), but not from usb_drv:
> QUIRK: Enable AMD PLL fix
>
> What might be going on? Why would usb_drv cause platform_drv to run out of
> CAPs, even when I assign it 2000 CAPs (instead of 800)?
>
> ------------------------------------------------------------
> ------------------
> Check out the vibrant tech community on one of the world's most
> engaging tech sites, Slashdot.org! http://sdm.link/slashdot
> _______________________________________________
> genode-main mailing list
> genode-main at lists.sourceforge.net
> https://lists.sourceforge.net/lists/listinfo/genode-main
>
>


-- 


Thank You,

Chris Rothrock
Senior System Administrator
(315) 308-1637
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.genode.org/pipermail/users/attachments/20180331/785e90bb/attachment.html>