foc_odroid_x2 with tftp boot via uboot on odroid u3

[Bernhard Blieninger]

Hi all,

tried something else instead.
Deleted the whole sd card again and flashed it with a fat32 partition 
starting at 1GB to ensure I don't write some place, that is rewritten 
when sd_fusing script writes boot data to sd card.
I feared that if i load 0x41000000 it could be the zImage kernel which 
is on the sd card already.

I also have to correct myself i have to use the usbnet uboot code from 
here: https://github.com/mkaczanowski/u-boot/tree/odroid-u3-usbnet
Otherwhise it wont boot the usb parts(network card).


Now I used the uImage from Ubuntu from the tftp server and the uImage 
from the genode build.
The boot.txt looks like this:

setenv ethact sms0
setenv ethaddr 00:10:75:2A:AE:E0
setenv gatewayip 192.168.0.254
setenv netmask 255.255.255.0
setenv serverip 131.159.12.22
setenv usbethaddr 00:10:75:2A:AE:E0
setenv ipaddr 192.168.0.23

usb start
tftp 0x70000000 odroid/uImage
bootm 0x70000000
bootm 0x41000000

Boot uImage now seem to work, Ubuntu runs to its kernel panic again but 
Genode now unfortunately hangs at Starting kernel.

Is it possible that now all is running as expected but x2 genode code 
can not be used at u3?
I'd expected that i should at least be able to boot, even if some usb 
drivers or something will not work?


Best regards,

Bernhard.



Here is the full log dump:


U-Boot 2010.12-00000-gb93fb15-dirty (Jan 18 2017 - 20:24:29) for Exynox4412


CPU: S5PC220 [Samsung SOC on SMP Platform Base on ARM CortexA9]
APLL = 1000MHz, MPLL = 880MHz
DRAM:  2 GiB

PMIC VERSION : 0x00, CHIP REV : 3
TrustZone Enabled BSP
BL1 version: 20121128


Checking Boot Mode ... SDMMC
MMC Device 0: 15343 MB
*** Warning - using default environment

In: serial
Out: serial
Err: serial
ModeKey Check... run normal_boot
Net: usb_ether
Hit any key to stop autoboot: 0
 >>> Load Boot Script from mmc 0:1 <<<
reading boot.scr
351 bytes read in 23 ms (14.6 KiB/s)
## Executing script at 40008000
(Re)start USB...
USB0:   Exynos4412-ehci: init hccr 12580000 and hcor 12580010 hc_length 16
usb: usb_refclk_enable is active low: YES
ProTIP: If usb doesn't work - try playing with 'usb_invert_clken' 
environment
USB EHCI 1.00
scanning bus 0 for devices... 3 USB Device(s) found
        scanning usb for storage devices... 0 Storage Device(s) found
        scanning usb for ethernet devices... 1 Ethernet Device(s) found
         scanning usb for keyboard ... Waiting for Ethernet 
connection... done.
Using sms0 device
TFTP from server 192.168.0.1; our IP address is 192.168.0.23; sending 
through4
Filename 'odroid/uImage'.
Load address: 0x70000000
Loading: #####################################################
          264.6 KiB/s
done
Bytes transferred = 773987 (bcf63 hex)
## Booting kernel from Legacy Image at 70000000 ...
    Image Name:
    Image Type:   ARM Linux Kernel Image (gzip compressed)
    Data Size:    773923 Bytes = 755.8 KiB
    Load Address: 41000000
    Entry Point: 41000000
    Verifying Checksum ... OK
    Uncompressing Kernel Image ... OK
ERROR: booting os 'Unknown OS' (3) is not supported
Boot with zImage

Starting kernel ...








On 26.01.2017 13:58, Bernhard Blieninger wrote:
> Hi Christian,
>
>
> thanks, this did not fix the problem either.
> I tested it with the uImage from ubuntu and the uImage from genode.
>
> Best regards,
>
> Bernhard.
>
>
>
> On 26.01.2017 11:15, Christian Helmuth wrote:
>> Hi,
>>
>> I've just a small hint regarding the following issue.
>>
>> On Wed, Jan 25, 2017 at 07:30:11PM +0100, Bernhard Blieninger wrote:
>>>   mkimage -A arm -C none -T script -n 'Custom Boot Script' -d 
>>> boot.txt boot.scr
>>>
>>> Problem now is that is says something like:
>>>
>>>     *ERROR: booting os 'Unknown OS' (3) is not supported*
>> When generating an uImage mkimage supports to set the operating system
>> in the commandline via '-O <os>'. So, your mkimage command line should
>> read
>>
>>    mkimage -A arm -O linux -C none -T script -n 'Custom Boot Script' 
>> -d boot.txt boot.scr
>>
>> Hope it helps
>
>
>
>
> ------------------------------------------------------------------------------
> Check out the vibrant tech community on one of the world's most
> engaging tech sites, SlashDot.org! http://sdm.link/slashdot
>
>
> _______________________________________________
> genode-main mailing list
> genode-main at lists.sourceforge.net
> https://lists.sourceforge.net/lists/listinfo/genode-main

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.genode.org/pipermail/users/attachments/20170126/37277522/attachment.html>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: smime.p7s
Type: application/pkcs7-signature
Size: 5192 bytes
Desc: S/MIME Cryptographic Signature
URL: <http://lists.genode.org/pipermail/users/attachments/20170126/37277522/attachment.bin>