Reagaring Genode and USB Armory
Martin Stein
martin.stein at ...1...
Wed Apr 27 13:09:27 CEST 2016
Hi Utkarsh,
I unsuccessfully tried to reproduce your problem with a fresh build. I
created a working SD card from the scratch with Genode version 16.02 by
just copying the commands from the tutorial in [1] to my bash and
filling in my parameters in the first section. I've attached the my UART
log to the mail.
The differences I see between your setup and mine:
* I've used the prebuilt Linux images for now. Is your setup working if
you're using prebuilt images? (You can do this by removing
<build_dir>/bin/linux*, <build_dir>/bin/rootfs* and <build_dir>/bin/dtb*
and restart from 'make run/tz_vmm')
* It seems that you're using another Uboot than me. Have you used the
boot loader that is created and installed by the tutorial or your own?
* The tutorials were tested only on Linux hosts. If you're using another
OS, you have to be aware of subtile differences. Also, there are
dedicated sections for other OS's in [2].
* It seems that your ether_gadget is missing something. In my setup it
says "g_ether gadget: high-speed config #1: CDC Ethernet (ECM)" which is
missing in your case. Consequently you're also missing "ifup: interface
usb0 already configured" when the VM configures its network interfaces.
And finally, your log says "IPv6: ADDRCONF(NETDEV_UP): usb0: link is not
ready".
Cheers,
Martin
[1]
https://github.com/genodelabs/genode/blob/master/repos/os/run/tz_vmm.run#L9
[2]
https://github.com/inversepath/usbarmory/wiki/Host-communication#cdc-ethernet
Am 26.04.2016 um 21:45 schrieb Agrawal, Utkarsh:
> Hello,
>
> The initial steps of compilation and building the SD card were not clear. It took me few days to understand whats going on with the building procedure. I will share the script file soon. There are some changes I am making to it. Then maybe you can incorporate it into the repository.
>
> I see that the wiki got updated. Thanks for that.
>
> Here is the link to the output: http://pasted.co/7ff78388
>
> Thank You
> Utkarsh
>
>
> ________________________________________
> From: Martin Stein <martin.stein at ...1...>
> Sent: Tuesday, April 26, 2016 2:19 PM
> To: Agrawal, Utkarsh
> Subject: Re: Reagaring Genode and USB Armory
>
> I have answered your last mail on the mailing list [1].
> It has the same subject line as this mail.
>
> Cheers,
> Martin
>
> [1] genode-main at lists.sourceforge.net
>
> Am 22.04.2016 um 11:17 schrieb Agrawal, Utkarsh:
>> Hello,
>>
>> Yes, I think it is a good time that we move it to the mailing list. How shall we do it?
>>
>> Thank You
>> Utkarsh
>>
>> ________________________________________
>> From: Martin Stein <martin.stein at ...1...>
>> Sent: Wednesday, April 20, 2016 5:07 PM
>> To: Agrawal, Utkarsh
>> Subject: Re: Reagaring Genode and USB Armory
>>
>> Hey Utkarsh,
>>
>> I would like to move this discussion to the mailing list at this point.
>>
>> Do you agree with that?
>>
>> Cheers,
>> Martin
>>
>> Am 20.04.2016 um 08:01 schrieb Agrawal, Utkarsh:
>>> Hello,
>>>
>>> I was able to Install ootloader, Genode, and the Linux rootfs. Thanks a lot for your guidance. I have compiled a script which does all this task easily. I would love to contribute this to the community, and would like to know how can I do it.
>>>
>>> Next steps as I see are:
>>> 1. Connect USB Armory to host machine via USB-to-TTL serial cable.
>>> 2. Connect to USB Armory COM port.
>>> 3. Insert USB Armory into host USB slot and interrupt auto boot on COM port.
>>> 4. Send bootloader commands on COM port:
>>> 5. Linux login: The login and password of the Linux guest are both "usbarmory"
>>>
>>> I hope the above steps are pretty straight forward, and there should be no issues there.
>>>
>>> Also, at [1], they mention about this "make ARCH=arm zImage LOADADDR=0x80008000 modules". I am not sure what image they are talking about, when am I supposed to do this step.
>>>
>>> Next I would like to know how do I start working on TrustZone with Genode. Can you guide me on how to start with a sample application which switches between Normal and Secure World?
>>>
>>> Thank You
>>> Utkarsh Agrawal
>>>
>>> [1] https://urldefense.proofpoint.com/v2/url?u=https-3A__github.com_inversepath_usbarmory_wiki_Genode-2DOS&d=CwIC-g&c=C3yme8gMkxg_ihJNXS06ZyWk4EJm8LdrrvxQb-Je7sw&r=hnUL4kgB9cStyuGpvYu3L9_MVOWR5t87hYpTv2FwCGo&m=NwzIeuHqYnvROYKinKAlZVd5PiAYFi9QCtcc7dRP5gs&s=xm51_erngIaEOyEFFbZcXPF_0997eNeTOB2sbteiTQU&e=
>>> ________________________________________
>>> From: Agrawal, Utkarsh
>>> Sent: Friday, April 15, 2016 11:12 PM
>>> To: Martin Stein
>>> Subject: Re: Reagaring Genode and USB Armory
>>>
>>> Hello,
>>>
>>> Thank for you the reply. I just noticed that the subject of the email has a typo. Maybe I was in a hurry when writing the first mail. :)
>>>
>>> I am sure that I was in the mentioned branch. I will try [2] after I have the basic setup running of Genode.
>>>
>>>
>>> I have been trying to use [1]. But I get some errors. Following are the steps I have followed:
>>>
>>> I cloned the master branch of https://urldefense.proofpoint.com/v2/url?u=https-3A__github.com_genodelabs_genode&d=CwIC-g&c=C3yme8gMkxg_ihJNXS06ZyWk4EJm8LdrrvxQb-Je7sw&r=hnUL4kgB9cStyuGpvYu3L9_MVOWR5t87hYpTv2FwCGo&m=NwzIeuHqYnvROYKinKAlZVd5PiAYFi9QCtcc7dRP5gs&s=fEOHYlETLJd9X5bo8qw783vUXEtk6k_2PtnJu8wVG_Y&e= at /home/genode/genode-master on my computer.
>>>
>>> I changed the following variables:
>>> export TARGET_DEV=/dev/sdc # empty boot medium
>>> export TARGET_MNT=/home/mnt # where to mount the boot medium
>>> export GENODE_DIR=/home/genode/genode-master # root of the Genode sources
>>> export BUILD_DIR=/path/build/hw_usb_armory # Genode build directory
>>>
>>> I am not so sure if the build directory should be what I mentioned there. I just chose a directory randomly.
>>>
>>> After this, I realized that in the :Install Genode: step there is no etc/build.conf file. I looked at /home/genode/genode-master and /home/genode/genode-master/repos/os/.
>>>
>>> To fix that I executed ./tool/create_builddir hw_usb_armory at /home/genode/genode-master
>>> Now I got a build directory with build.conf in hw_usb_armory folder.
>>>
>>> I copied over the build.conf to /home/genode/genode-master/repos/os/etc
>>>
>>> Next I tried running make run/tz_vmm.run. But now it just says that make: 'tz_vmm.run' is up to date. I don't think that the build process ever started.
>>>
>>> I am not sure if I am missing any steps here.
>>>
>>> Thank You
>>> Utkarsh
>>>
>>>
>>> ________________________________________
>>> From: Martin Stein <martin.stein at ...1...>
>>> Sent: Friday, April 15, 2016 3:06 PM
>>> To: Agrawal, Utkarsh
>>> Subject: Re: Reagaring Genode and USB Armory
>>>
>>> Hi Utkarsh,
>>>
>>> Am 14.04.2016 um 19:30 schrieb Agrawal, Utkarsh:
>>>> I landed on [2], using the USB Armory page for Genode[3]. The script fails at this line "make usbarmory_defconfig". It says something like the target was not found for make.
>>>
>>> I was not able to reproduce this but I noticed that [3] doesn't
>>> reference the appropriate branch in my linux repo. Are you sure that
>>> you're using the 'genode_hw_usb_armory_tz_vmm' branch as mentioned in [2]?
>>>
>>>> So as you said, for our own Linux guest, we can use [2]. Just to have a clear idea on this, will I have to combine partial instructions from [1], and the rest from [2] to be able to run our own guest?
>>>
>>> Script [2] copies the images (linux, dtb, rootfs) that are normally
>>> downloaded by script [1] to $TARGET_DIR so you want to 'export
>>> TARGET_DIR=<YOUR_GENODE_BUILD_DIR>/bin' under ':User settings:' in
>>> script [2]. So, if you examine script [2] first, script [1] afterwards
>>> automatically uses the custom images instead of downloading others.
>>>
>>>> Also, I request you to kindly look at [3], and put up relevant details there. As because of [3] I was going around in circles, and could have never landed on [1].
>>>
>>> Thank you for the hint. I will redirect it to the Inversepath staff. The
>>> content of the wiki is up to them and I would suggest you to preferably
>>> use [1] and [2] for the Genode-related stuff.
>>>
>>> Cheers,
>>> Martin
>>>
>>> [1] https://urldefense.proofpoint.com/v2/url?u=https-3A__github.com_genodelabs_genode_blob_master_repos_os_run_tz-5Fvmm.run&d=CwID-g&c=C3yme8gMkxg_ihJNXS06ZyWk4EJm8LdrrvxQb-Je7sw&r=hnUL4kgB9cStyuGpvYu3L9_MVOWR5t87hYpTv2FwCGo&m=-kQoV0ZR_iKUnT8nma7ny9LQLjMXq6a0nxua4xY9Vvc&s=NuzhEEEQyHw-TZI6tVhCu8Pz_l-HrCEDCFikY5nicdc&e=
>>>
>>> [2]
>>> https://urldefense.proofpoint.com/v2/url?u=https-3A__github.com_m-2Dstein_genode-5Fbinaries_blob_master_tz-5Fvmm_usb-5Farmory_README&d=CwID-g&c=C3yme8gMkxg_ihJNXS06ZyWk4EJm8LdrrvxQb-Je7sw&r=hnUL4kgB9cStyuGpvYu3L9_MVOWR5t87hYpTv2FwCGo&m=-kQoV0ZR_iKUnT8nma7ny9LQLjMXq6a0nxua4xY9Vvc&s=oalYTQJt3AWOozXVTtm3IFcPDdIsgqQyHW8O6atsVwk&e=
>>>
>
> ------------------------------------------------------------------------------
> Find and fix application performance issues faster with Applications Manager
> Applications Manager provides deep performance insights into multiple tiers of
> your business applications. It resolves application problems quickly and
> reduces your MTTR. Get your free trial!
> https://ad.doubleclick.net/ddm/clk/302982198;130105516;z
> _______________________________________________
> genode-main mailing list
> genode-main at lists.sourceforge.net
> https://lists.sourceforge.net/lists/listinfo/genode-main
>
-------------- next part --------------
port is : /dev/ttyUSB0
flowcontrol : none
baudrate is : 115200
parity is : none
databits are : 8
escape is : C-a
local echo is : no
noinit is : no
noreset is : yes
nolock is : yes
send_cmd is : sz -vv
receive_cmd is : rz -vv
imap is :
omap is :
emap is : crcrlf,delbs,
Terminal ready
U-Boot 2014.07-gac8dbd7 (Apr 27 2016 - 12:24:28)
Board: USB armory
I2C: ready
DRAM: 512 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
In: serial
Out: serial
Err: serial
Net: CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot: 0
** File not found /boot/uImage **
** File not found /boot/imx53-usbarmory.dtb **
Wrong Image Format for bootm command
ERROR: can't get kernel image!
=> ext2load mmc 0:1 0x74000000 /uImage
3181737 bytes read in 208 ms (14.6 MiB/s)
=> bootm 0x74000000
## Booting kernel from Legacy Image at 74000000 ...
Image Name:
Image Type: ARM Linux Kernel Image (gzip compressed)
Data Size: 3181673 Bytes = 3 MiB
Load Address: 72000000
Entry Point: 72000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Starting kernel ...
kernel initialized
Genode 16.02
int main(): --- create local services ---
int main(): --- start init ---
int main(): transferred 246 MB to init
int main(): --- init created, waiting for exit condition ---
[init] Could not open ROM session for module "ld.lib.so"
[init] parent provides
[init] service "ROM"
[init] service "RAM"
[init] service "IRQ"
[init] service "IO_MEM"
[init] service "IO_PORT"
[init] service "CAP"
[init] service "PD"
[init] service "RM"
[init] service "CPU"
[init] service "LOG"
[init] service "SIGNAL"
[init] service "VM"
[init] child "gpio_drv"
[init] RAM quota: 2863104
[init] ELF binary: gpio_drv
[init] priority: 0
[init] provides service Gpio
[init] child "timer"
[init] RAM quota: 2863104
[init] ELF binary: timer
[init] priority: 0
[init] provides service Timer
[init] child "platform_drv"
[init] RAM quota: 2863104
[init] ELF binary: platform_drv
[init] priority: 0
[init] provides service Regulator
[init] provides service Platform
[init] child "sd_card_drv"
[init] RAM quota: 2863104
[init] ELF binary: sd_card_drv
[init] priority: 0
[init] provides service Block
[init] child "part_blk"
[init] RAM quota: 10203136
[init] ELF binary: part_blk
[init] priority: 0
[init] provides service Block
[init] child "tz_vmm"
[init] RAM quota: 10203136
[init] ELF binary: tz_vmm
[init] priority: 0
[init -> platform_drv] --- i.MX53 platform driver ---
[init] child "platform_drv" announces service "Platform"
[init -> sd_card_drv] --- Imx53 SD card driver ---
[init] child "sd_card_drv" announces service "Block"
[init] child "timer" announces service "Timer"
[init -> tz_vmm] Start virtual machine ...
[init -> gpio_drv] --- i.MX53 gpio driver ---
[init -> gpio_drv] No GPIO config
[init] child "gpio_drv" announces service "Gpio"
[init -> sd_card_drv] CID: 0x1b534d30 0x30303030 0x10e59f30 0x8400eb00
[init -> sd_card_drv] RCA: 0x59b4
[init -> sd_card_drv] SD card detected
[init -> sd_card_drv] capacity: 7655 MiB
Quota exceeded! amount=12288, size=12288, consumed=12288
[init -> part_blk] Partition 1: LBA 20480 (194560 blocks) type: 83
[init -> part_blk] Partition 2: LBA 215040 (3895296 blocks) type: 83
[init] child "part_blk" announces service "Block"
[init -> tz_vmm] [vm] Booting Linux on physical CPU 0x0
[init -> tz_vmm] [vm] Linux version 4.2.3-00002-gfd57dbf-dirty (lypo at ...207...) (gcc version 4.9.3 20150113 (prerelease) (Linaro GCC 4.9-2015.01-3) ) #4 PREEMPT Thu Nov 12 15:18:30 CET 2015
[init -> tz_vmm] [vm] CPU: ARMv7 Processor [412fc085] revision 5 (ARMv7), cr=10c5387d
[init -> tz_vmm] [vm] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[init -> tz_vmm] [vm] Machine model: Inverse Path USB armory
[init -> tz_vmm] [vm] Memory policy: Data cache writeback
[init -> tz_vmm] [vm] CPU: All CPU(s) started in SVC mode.
[init -> tz_vmm] [vm] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[init -> tz_vmm] [vm] Kernel command line: console=ttyS0 root=/dev/sda1 rootwait rw init=/sbin/init clk_ignore_unused
[init -> tz_vmm] [vm] PID hash table entries: 1024 (order: 0, 4096 bytes)
[init -> tz_vmm] [vm] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[init -> tz_vmm] [vm] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[init -> tz_vmm] [vm] Memory: 255160K/262144K available (3174K kernel code, 119K rwdata, 1060K rodata, 140K init, 93K bss, 6984K reserved, 0K cma-reserved)
[init -> tz_vmm] [vm] Virtual kernel memory layout:
[init -> tz_vmm] [vm] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[init -> tz_vmm] [vm] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[init -> tz_vmm] [vm] vmalloc : 0x90800000 - 0xff000000 (1768 MB)
[init -> tz_vmm] [vm] lowmem : 0x80000000 - 0x90000000 ( 256 MB)
[init -> tz_vmm] [vm] modules : 0x7f000000 - 0x80000000 ( 16 MB)
[init -> tz_vmm] [vm] .text : 0x80008000 - 0x8042abfc (4235 kB)
[init -> tz_vmm] [vm] .init : 0x8042b000 - 0x8044e000 ( 140 kB)
[init -> tz_vmm] [vm] .data : 0x8044e000 - 0x8046bc60 ( 120 kB)
[init -> tz_vmm] [vm] .bss : 0x8046bc60 - 0x804833ac ( 94 kB)
[init -> tz_vmm] [vm] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[init -> tz_vmm] [vm] Preemptible hierarchical RCU implementation.
[init -> tz_vmm] [vm] Build-time adjustment of leaf fanout to 32.
[init -> tz_vmm] [vm] NR_IRQS:16 nr_irqs:16 16
[init -> tz_vmm] [vm] TrustZone Interrupt Controller (TZIC) initialized
[init -> tz_vmm] [vm] CPU identified as i.MX53, unknown revision
[init -> tz_vmm] [vm] Switching to timer-based delay loop, resolution 29ns
[init -> tz_vmm] [vm] sched_clock: 32 bits at 33MHz, resolution 29ns, wraps every 64424507889ns
[init -> tz_vmm] [vm] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 57337812242 ns
[init -> tz_vmm] [vm] Console: colour dummy device 80x30
[init -> tz_vmm] [vm] console [ttyS0] enabled
[init -> tz_vmm] [vm] Calibrating delay loop (skipped), value calculated using timer frequency.. 66.66 BogoMIPS (lpj=333333)
[init -> tz_vmm] [vm] pid_max: default: 32768 minimum: 301
[init -> tz_vmm] [vm] Security Framework initialized
[init -> tz_vmm] [vm] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[init -> tz_vmm] [vm] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[init -> tz_vmm] [vm] Initializing cgroup subsys net_cls
[init -> tz_vmm] [vm] CPU: Testing write buffer coherency: ok
[init -> tz_vmm] [vm] Setting up static identity map for 0x80008200 - 0x80008258
[init -> tz_vmm] [vm] devtmpfs: initialized
[init -> tz_vmm] [vm] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 2
[init -> tz_vmm] [vm] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[init -> tz_vmm] [vm] pinctrl core: initialized pinctrl subsystem
[init -> tz_vmm] [vm] NET: Registered protocol family 16
[init -> tz_vmm] [vm] DMA: preallocated 256 KiB pool for atomic coherent allocations
[init -> tz_vmm] [vm] cpuidle: using governor ladder
[init -> tz_vmm] [vm] cpuidle: using governor menu
[init -> tz_vmm] [vm] imx53-pinctrl 53fa8000.iomuxc: initialized IMX pinctrl driver
[init -> tz_vmm] [vm] 50000000.aips:usbphy at ...361... supply vcc not found, using dummy regulator
[init -> tz_vmm] [vm] 50000000.aips:usbphy at ...23... supply vcc not found, using dummy regulator
[init -> tz_vmm] [vm] pps_core: LinuxPPS API ver. 1 registered
[init -> tz_vmm] [vm] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti at ...292...>
[init -> tz_vmm] [vm] clocksource: Switched to clocksource mxc_timer1
[init -> tz_vmm] [vm] NET: Registered protocol family 2
[init -> tz_vmm] [vm] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[init -> tz_vmm] [vm] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[init -> tz_vmm] [vm] TCP: Hash tables configured (established 2048 bind 2048)
[init -> tz_vmm] [vm] UDP hash table entries: 256 (order: 0, 4096 bytes)
[init -> tz_vmm] [vm] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[init -> tz_vmm] [vm] NET: Registered protocol family 1
[init -> tz_vmm] [vm] futex hash table entries: 256 (order: -1, 3072 bytes)
[init -> tz_vmm] [vm] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[init -> tz_vmm] [vm] io scheduler noop registered (default)
[init -> tz_vmm] [vm] imx-sdma 63fb0000.sdma: failed to get firmware from device tree
[init -> tz_vmm] [vm] imx-sdma 63fb0000.sdma: initialized
[init -> tz_vmm] [vm] ttyS0 at MMIO 0x1 (irq = 0, base_baud = 230400) is a IMX
[init -> tz_vmm] [vm] loop: module loaded
[init -> part_blk] session opened at partition 2 for 'tz_vmm -> sda1'
[init -> tz_vmm] [vm] genblk: drive 0
[init -> tz_vmm] [vm] block count 3895296
[init -> tz_vmm] [vm] block size 512
[init -> tz_vmm] [vm] writeable 1
[init -> tz_vmm] [vm] queue size 5226480
[init -> tz_vmm] [vm] pirq 92
[init -> tz_vmm] [vm] virq 108
[init -> tz_vmm] [vm] major number 254
[init -> tz_vmm] [vm] name "sda1"
[init -> tz_vmm] [vm] device-mapper: ioctl: 4.33.0-ioctl (2015-8-18) initialised: dm-devel at ...315...
[init -> tz_vmm] [vm] sahara 63ff8000.crypto: SAHARA version 4 initialized
[init -> tz_vmm] [vm] NET: Registered protocol family 17
[init -> tz_vmm] [vm] GENODE_TZ_VMM: skip mx5_cpu_lp_set
[init -> tz_vmm] [vm] imx5_pm_common_init: No DDR LPM support with suspend -22!
[init -> tz_vmm] [vm] hctosys: unable to open rtc device (rtc0)
[init -> tz_vmm] [vm] clk: Not disabling unused clocks
[init -> tz_vmm] [vm] EXT4-fs (sda1): couldn't mount as ext3 due to feature incompatibilities
[init -> tz_vmm] [vm] EXT4-fs (sda1): couldn't mount as ext2 due to feature incompatibilities
[init -> tz_vmm] [vm] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[init -> tz_vmm] [vm] VFS: Mounted root (ext4 filesystem) on device 254:0.
[init -> tz_vmm] [vm] devtmpfs: mounted
[init -> tz_vmm] [vm] Freeing unused kernel memory: 140K (8042b000 - 8044e000)
INIT: version 2.88 booting
[init -> tz_vmm] [vm] [info] Using makefile-style concurrent boot in runlevel S.
[init -> tz_vmm] [vm] random: nonblocking pool is initialized
[init -> tz_vmm] [vm] [....] Starting the hotplug events dispatcher: udevdudevd[150]: starting version 175
[ ok -> tz_vmm] [vm] .
[ ok -> tz_vmm] [vm] [....] Synthesizing the initial hotplug events...done.
[init -> tz_vmm] [vm] [....] Waiting for /dev to be fully populated...imx2-wdt 53f98000.wdog: timeout 60 sec (nowayout=0)
[init -> tz_vmm] [vm] usbcore: registered new interface driver usbfs
[init -> tz_vmm] [vm] usbcore: registered new interface driver hub
[init -> tz_vmm] [vm] usbcore: registered new device driver usb
[init -> tz_vmm] [vm] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ ok -> tz_vmm] [vm] done.
[ ok -> tz_vmm] [vm] [....] Activating swap...done.
[init -> tz_vmm] [vm] EXT4-fs (sda1): re-mounted. Opts: (null)
[ ok -> tz_vmm] [vm] [....] Cleaning up temporary files... /tmp.
[init -> tz_vmm] [vm] [info] Loading kernel module ledtrig_heartbeat.
[init -> tz_vmm] [vm] FATAL: Module ledtrig_heartbeat not found.
[init -> tz_vmm] [vm] [info] Loading kernel module g_ether.
[init -> tz_vmm] [vm] using random self ethernet address
[init -> tz_vmm] [vm] using random host ethernet address
[init -> tz_vmm] [vm] using self ethernet address: 1a:55:89:a2:69:41
[init -> tz_vmm] [vm] usb0: HOST MAC 92:dd:96:ea:8d:c5
[init -> tz_vmm] [vm] usb0: MAC 1a:55:89:a2:69:41
[init -> tz_vmm] [vm] using random self ethernet address
[init -> tz_vmm] [vm] using random host ethernet address
[init -> tz_vmm] [vm] g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
[init -> tz_vmm] [vm] g_ether gadget: g_ether ready
[init -> tz_vmm] [vm] g_ether gadget: high-speed config #1: CDC Ethernet (ECM)
[ ok -> tz_vmm] [vm] [....] Activating lvm and md swap...done.
[init -> tz_vmm] [vm] [....] Checking file systems...fsck from util-linux 2.20.1
[ ok -> tz_vmm] [vm] done.
[ ok -> tz_vmm] [vm] [....] Mounting local filesystems...done.
[ ok -> tz_vmm] [vm] [....] Activating swapfile swap...done.
[ ok -> tz_vmm] [vm] [....] Cleaning up temporary files....
[ ok -> tz_vmm] [vm] [....] Setting kernel variables ...done.
[init -> tz_vmm] [vm] [....] Configuring network interfaces...ifup: interface usb0 already configured
[ ok -> tz_vmm] [vm] done.
[ ok -> tz_vmm] [vm] [....] Cleaning up temporary files....
[init -> tz_vmm] [vm] NET: Registered protocol family 10
INIT: Entering runlevel: 2
[init -> tz_vmm] [vm] [info] Using makefile-style concurrent boot in runlevel 2.
[ ok -> tz_vmm] [vm] [....] Starting enhanced syslogd: rsyslogd.
[ ok -> tz_vmm] [vm] [....] Starting periodic command scheduler: cron.
[ ok -> tz_vmm] [vm] [....] Starting OpenBSD Secure Shell server: sshd.
[init -> tz_vmm] [vm]
[init -> tz_vmm] [vm] Debian GNU/Linux 7 usbarmory console
[init -> tz_vmm] [vm]
More information about the users
mailing list