Data Abort MMU exception on mapped IO register read

[robjsstewart at ...196...]

Thanks for the input Tim, but enabing the clock was the first thing I did, as with all the other devices I use. There are power management status registers in the Control Module. The bits in their identify that the PRUSS modules I'm trying to access have power and the memory power is on. Also, the. clock control enable bit is happily sitting at 2 indicating the clock is running. 

Everything seems to point to something about the translation table enties, or the lack thereof.

Bob

Sent from my android device.

-----Original Message-----
From: Tim Newsham <tim.newsham at ...9...>
To: Genode OS Framework Mailing List <genode-main at lists.sourceforge.net>
Sent: Mon, 13 Apr 2015 12:52 PM
Subject: Re: Data Abort MMU exception on mapped IO register read

not sure if its this (error code seems to indicate otherwise)
but on the am335x you need to enable the various units
otherwise they do not appear at their physical addresses
at all, and reading from the address will get you a trap.



On Mon, Apr 13, 2015 at 2:41 AM, Bob Stewart <robjsstewart at ...196...> wrote:
> Hi,
>
> I'm running with 15.02, base-hw on a TI AM3359 processor. I've
> successfully created device drivers for most of the devices on the
> peripheral bus without issue. Accessing the the final device i need a
> driver for, is causing me fits.
>
> I attached the IO device register space with the usual creation of a
> Attached_io_mem_dataspace  based object which also uses the very useful
> MMIO utility object. I also tried it without MMIO and just accessed the
> space through local_addr<void>.
>
> When I try to read an address in the mapped space I get an "unknown MMU
> exception". When I write to the same address no error occurs (I'm
> assuming for now it's failing silently). Putting PDBG's in the arm
> thread code shows that the error on the read is is being caused by a
> DATAT_ABORT. Peeking at the data fault status register (dfsr) shows
> 0x805 which according the the the ARM7 technical reference manual
> decodes to a translation table error.
>
> The virtual address created when the io device is mapped is 0x81B0_0000
> (the load_addr<void>), but I see no section table entry being created
> for 0x8100_0000. Only one is created at 0x8000_0000. If I'm remembering
> correctly sections are 16 MB is size for this architecture. I'm
> instrumenting short_translation_table.h to see what translation table
> entries are being created. I also don't seen any short translation table
> entries being created in the 0x81bxx_xxxx region.
>
> My platform support code does include the physical address and size for
> the region containing the device I'm trying to access.
>
> The only physical difference with this device and the others I've
> successfully created drivers for, is that is runs of the L4
> interconnection whereas the others were on the L3 interconnect. In this
> SoC the L4 is bridged to the L3 interconnect and runs at half the speed
> of the L3 bus. But I doubt that this would make any difference to the
> mapping of the device. This device is also much higher in memory that
> the other devices.
>
> Any hints at further debugging of this issue would be greatly appreciated.
>
> Thanks,
>              Bob Stewart
>
>
> ------------------------------------------------------------------------------
> BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT
> Develop your own process in accordance with the BPMN 2 standard
> Learn Process modeling best practices with Bonita BPM through live exercises
> http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_
> source=Sourceforge_BPM_Camp_5_6_15&utm_medium=email&utm_campaign=VA_SF
> _______________________________________________
> genode-main mailing list
> genode-main at lists.sourceforge.net
> https://lists.sourceforge.net/lists/listinfo/genode-main



-- 
Tim Newsham | www.thenewsh.com/~newsham | @newshtwit | thenewsh.blogspot.com

------------------------------------------------------------------------------
BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT
Develop your own process in accordance with the BPMN 2 standard
Learn Process modeling best practices with Bonita BPM through live exercises
http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_
source=Sourceforge_BPM_Camp_5_6_15&utm_medium=email&utm_campaign=VA_SF
_______________________________________________
genode-main mailing list
genode-main at lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/genode-main
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.genode.org/pipermail/users/attachments/20150413/f57e1c1a/attachment.html>